USED ITEMS FOR SALE

We come into used items and equipment from time to time that are still servicable and in good working order, but out of warranty.  Some are on consignment from customers who asked us to help them sell the items for them.  If you see something you are interested in, let us know.  We can install items such as boat lifts for you and you can get a good, used product at a reduced cost!  We hope you find this page worth the visit!

Used Boat Lifts:

(Note:  Representative picture of 4,000 lb. Doozie lift - actual lift is disassembled at our shop)

Listed June 23, 2007 - ITEM # 4KDOOZ:  4,000 lb Doozie Low Profile Lift (Galvanized) - This lift is about 5 years old, but was in good working condition when disassembled for a newer, larger lift.  The Doozie 4,000 lb. Low Profile Lift has one motor and driveshaft on the two pilings opposite the floating dock or pier and uses a cable and pulley routing system that goes under the boat to lift it.  This cable routing method allows the owner to have a clear opening on the dockside with no overhead beam or driveshaft on that side.  The lift is designed for smaller boats - the lifting beams are only 10' wide, leaving less than 9' clearance for boat entry.  It is designed to be installed on four treated round pilings spaced approximately 11' x 11' and requires 120V or 240V power to operate, depending on the distance from the source panel box to the lift location.  It has wooden cradle bunks designed for a V-Bottom boat.  It has stainless steel cables that wrap on smooth, two compartment cable drums and requires periodic greasing and occasional pulley belt tightening to maintain operation.  The drive unit is a dual phased 3/4 hp motor mounted on a flat plate gear drive with a 6" flywheel and pulley belt under a plastic cover.  Lift range is 10', lift speed is approximately 2' per minute.

Price = $ 800.00 as is, $2,400.00 installed (less electrical) 

(Note:  Representative picture of 7,000 lb. Doozie lift - actual lift is disassembled at our shop)

Listed June 23, 2007 - ITEM # 7KDOOZ:  7,000 lb Doozie Low Profile Lift (Galvanized) - This lift is about 5 years old, but was in good working condition when disassembled for a newer, larger lift.  The Doozie 7,000 lb. Low Profile Lift is the big brother to the 4,000 lb model above and, like the 4,000 lb model, has one motor and driveshaft on the two pilings opposite the floating dock or pier and uses a cable and pulley routing system that goes under the boat to lift it.  This cable routing method allows the owner to have a clear opening on the dockside with no overhead beam or driveshaft on that side.  The lift is designed for larger boats - the lifting beams are 11' wide, allowing more clearance for boat entry.  It is designed to be installed on four treated round pilings spaced approximately 12' x 12' and requires 120V or 240V power to operate, depending on the distance from the source panel box to the lift location.  It has wooden cradle bunks designed for a V-Bottom boat.  It has stainless steel cables that wrap on smooth, two compartment cable drums and requires periodic greasing and occasional pulley belt tightening to maintain operation.  The drive unit is a dual phased 3/4 hp motor mounted on a flat plate gear drive with a 10" flywheel and pulley belt under a plastic cover.  Lift range is 10', lift speed is approximately 2' per minute.

Price = $ 1,200.00 as is, $2,800.00 installed (less electrical) 

MISCELLANEOUS ITEMS FOR SALE

(The longer left hinge bracket is visible here) 

Listed June 23, 2007 - ITEM # 4x20GALVRAMP:  We have a 4'x20' galvanized down ramp (gangway) that was built for a fixed pier end that was a couple of inches out of square on the end where the ramp attached to it.  The customer opted for a wooden ramp instead.  This is a new ramp that has one hinge plate on one side 2" longer than the other side where the hinge rod connects the ramp to the pier end.  The hinge plate could be drilled to match the other side and the hinge plate cut shorter so both ends bolted up square to your dock.  All that is needed besides the hinge plate modification is wood decking and you will have a nice galvanized ramp with railings on your dock.

Price = $ 900.00 as is, $ 1,300.00 with the hinge plate modifcation and decking lumber screwed down.  You pick it up or we will deliver to your site for $75.00, if you want us to hook it up to your pier we will install it for $300.00 additional assuming normal installation techniques.

Listed June 23, 2007 - ITEM # COMPRESSOR:  We have a good, used 4,000 psi air compressor that is diesel powered and portable.  It needs a new coat of paint and a battery, but starts and runs when it has a good charge.  The kill switch needs repair, but we would shut it down by using the choke.  It has multiple filter stages, and was originally used to fill scuba tanks, then later used on a paintball field.  The unit is large and heavy, and will require a trailer to move it.  Can be used for filling scuba tanks, paintball air tanks, tires or balloons (not helium).  You will need a fill station connection to match whichever function you choose to use it for.

Price = $ 1,500.00 as is.